Sagemcom router: step-by-step setup for a teapot. Universal router from Rostelecom Sagemcom f st 2804 v7 reset

In the interface that opens, select the "Advanced Settings" tab and click the "Add" button.

The connection creation window will open. Here we specify the VPI and VCI for the Internet connection. In our area it is 0/33. We do not change anything else, click the "Apply / Save" button.
Now let's add a connection for IPTV. Click the "Add" button again:

We set VPI and VCI to 0/50 (there may be others in your Rostelecom branch), click the "Apply / Save" button. Thus, we have created 2 second level interfaces for ADSL.

Now we need to create WAN services. To do this, select the "Advanced settings" item in the menu on the left, select the "WAN service" tab in it. We delete the prescribed interfaces by first ticking the "Delete" column.

Please note that the remote services had the eth3.2 interface listed in the Interface column. This means that this router was configured by default for FTTB. This connection must also be removed. To do this, in the menu on the left, select the item Additional settings >>> Level 2 interface, tab ETH interface and remove the eth3 interface there.

Setting up PPPoE for Rostelecom

We return to the "WAN service" tab. Click the "Add" button.

Select from the drop-down tab "atm0 / (0_0_33)" for the Internet and click the "Next" button.

Depending on the type of connection, select either "PPPoE" or "Bridging". In the first case, the modem will be configured in router mode, it will itself connect to the Internet and distribute it to connected devices. It is best to configure the router in router mode. It is not advisable to set up an Internet connection in bridge mode. We press the "Next" button.

We hammer in the login and password from the card, click the "Next" button.
In the following windows, do not change anything, click "Next". The only thing worth paying attention to is that if the usb0 interface instead of ppp1 is in the columns on the left, it will need to be moved to the right column, and the ppp1 interface, respectively, to the left. At the end, click "Apply/Save".
We get the following table in the WAN service section:

Digital television IPTV for Rostelecom.

In the WAN service section, click the "Add" button to create an IPTV configuration:

Select from the drop-down tab "atm1 / (0_0_50)" and click the "Next" button.

It remains only to group the ports for the correct operation of the two services.

grouping of ports.

Go to the "Interface grouping" tab, delete the default IPTV group by checking the Delete box.

Then click "Add". The following window will open:

In the "Group Name" field, write a name, let's say TV, select the previously created connection to IPTV on the right and click on the arrow to move it to the left side. In the same way below, we bind ports to this connection, let it be port 4 on the router - “eth3”. Click the Apply/Save button.
It should turn out like this.

Universal router [email protected], v7 rev.1 is compliant with the 802.11b/g/n WFA specification and allows connection speeds up to 300 Mbps. 2 USB 2.0 ports, work with 3G USB modem

Sagemcom [email protected] 2804, v7 rev.1 can work both via xDSL technology and via utp cable. Those. There are WAN ports for both types of connection technology. This fact should be taken into account when configuring the connection. We will reflect this in the Internet connection settings item. I would also like to note that Sagemcom [email protected] 2804, v7 rev.1 can only be configured for PPPoE connection or bridge mode.

Instructions for setting up a Sagemcom router [email protected] 2804 v7 rev.1 and Sagemcom [email protected] 2804v7 rev.1B

Authorization

In order to get into the web interface of the router, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Features of setting modem + wi-fi router

1. This modem has an ip-address 192.168.1.1. Therefore, if you connect to Sagemcom 2804 router Asus, NetGear, Tp Link or ZyXEL(these models of routers have the same ip-address - 192.168.1.1) - do not forget to change the address of one of the devices to some other one, for example 192.168.0.1

2. There are two setting options:

• modem Sagemcom 2804 configures it in router mode (PPPoE Internet connection is created on the modem), and on the router select the Static IP (Static IP) or Dinamic IP (DHCP or Dynamic IP) mode;
• modem Sagemcom 2804 configure in bridge mode (bridge), and create an Internet connection (PPPoE) on the router;

3. If the subscriber has an IP-TV service, then on the modem Sagemcom 2804 DHCP will be disabled. Therefore, on the router, you select the connection type Static IP (Static IP) and prescribe ip-addresses manually.

Setting up Wi-Fi on the router

1. Find the menu item on the left WLAN setting;, in the window that opens, check that there is a check mark on the parameter Enable wireless; and Enable multicast transmission over wireless network (WMF);. SSID- the name of the wireless connection, leave it by default or change it to your own, press the button Apply/Save;

2. Next, open the Security submenu, on the left and in the tab that opens turn off the WPS option, check that authentication is selected WPA-PSK, encryption WPA-TKIP+AES. We either prescribe our own network protection with a key, or press the button opposite WPA/WAP To display, click here; and in the window that opens, rewrite the password. Click Apply/Save;

Internet connection setup

Before setting the router settings, you need to reset its settings to factory settings. To do this, go to Settings;→ Reset;→ Restore default settings;.

The window below will appear in front of you. We expect 2 minutes.

After resetting the default settings, you need to remove unnecessary add-ons from the router. Go to the tab. Next, check 3 checkboxes as shown in the screenshot below and click Delete;.

Next, go to the tab Additional settings;→ 2nd level interface;. Next, check the only checkbox as shown in the screenshot below and click Delete;.

Internet setup via xDSL

Additional settings;, Layer 2 interface;. We press the button Add; in the middle of the window.

We follow the setup wizard ;, we fix only 2 points VPI and VCI for the parameters that Rostelecom uses. Click Apply/Save;

We check that the appropriate layer 2 interface is selected (in our example it is 0_0_35) and press Further;

In the WAN service configuration, decide how the modem (router, bridge) will be configured and click Further;(see an example of setting by a router)

In the window that appears, enter PPP username;- login, PPP password;- password. PPPoE service name;- any. Put a tick in the box retry PPP on authentication failure; and Enable IGMP Multicast Proxy;, Further;

In the next two windows of the wizard; check that the created interfaces are in the left column. If they are in the right - transfer to the left, press Further;

Internet setup via ETTH

Go to tab Additional settings;→ ETH interface;. If this is empty, then add an entry. If Already available, then do not change anything (by default, a WAN port for eth0 is created - the first LAN port).

Go to tab Additional settings;→ WAN service;. Click Add;.

choose eth0/et0 Further;.

Put a dot on PPP over Ethernet (PPPoE), press Further;.

Type in section Username; enter the username of the subscriber, respectively, in Password;- subscriber's password, PPPoE service name;- int. Click Further;.

Then the left column Available routable WAN interfaces; highlight the item ppp1.1; and press the button <- . Click Further;. Similarly, then in the left column Available WAN interfaces; highlight the item ppp1.1; and press the button <- . Click Further;.

Setting up IP TV

Setting up IP-TV for different connection technologies is different.

Setting up IP-TV via xDSL

In the main window, click the menu item on the left Additional settings;, Layer 2 interface;. In the table that appears, if there are already configured connections for IP-TV, delete them (delete first in the WAN service menu, then in the Layer 2 Interface). Then we press the button Add; in the middle of the window.

We fix only 2 points VPI and VCI for the parameters used by Rostelecom. Click Apply/Save; at the bottom of the window (in the picture, the Rostelecom Omsk setting)

We add another interface to the WAN service configuration, where we check that the appropriate layer 2 interface is selected (in our example it is 0_1_36) and click Further;

For the modem to work correctly with STB set-top boxes (IPTV), you must go to the LAN parameter in the left menu and disable DHCP (Dynamic Host Configuration Protocol) in the window that appears. Then check that IGMP Snooping is enabled and click the button below Apply/Save;

Go to Grouping of interfaces and press Add;.

Create a group:

• Group name; - any, for example IPTV;
• We throw the desired connection to the left column using the special arrows;
• We transfer the desired LAN port to the left column. Just do not forget that the serial number of the LAN port written on the device case is one digit more than the one in the WEB interface. That is, if I want to connect the fourth port to television, then I transfer eth3 in the WEB interface;

As you can see, we got two groups - one for IPTV, the second - with everything else (the remaining LAN ports and WiFi). But that's not all!

Go to the LAN tab; and in the Group name field; choose ours, created for IPTV.

Put a tick on Enable IGMP Snooping; and press Apply/Save;.

Setting up IP-TV via ETTH

Go to tab Additional settings;→ WAN service;. Click Add;.

choose eth0/et0(or the interface you created above) and click Further;.

Put a dot on Bridging, press Further;.

Port Forwarding/Forwarding

Select NAT ---> Virtual Servers ---> Add

Use interface: select the interface you have created for the Internet (in our example it is xDSL)

Service name:- either choose from the list, or create your own.

Server IP address: address of the device on the network to which the request will be redirected

External portInternal port: range of ports to open

This router is well known to people who use the services of the Rostelecom operator, because it is this company that issues SAGEMCOM to its users [email protected] 2804v7. The device has a good signal and stable operation, it has a nice design, enviable characteristics and wide functionality. An important plus is the presence of USB ports, using which you can activate a 3G modem and create a backup channel.

Users have the ability to connect a 3G modem to the router

Let's take a closer look at how to configure SAGEMCOM [email protected] 2804v7!

• high power router CPU;
• IPTV;
• filtering by MAC address;
• compatibility with different devices;
• support for multiple IP services;
• when connected to a telephone wire, the line remains free;
• Rostelecom provides technical support;
• impact-resistant case;
• 300 Mbps;
• communication channels are switched automatically when problems occur.

The equipment can be controlled remotely, made possible by the TR-069 client. The device from SAGEMCOM also supports modern IP services: DHCP, DNS, IPv6, IGMP, IP routing (full speed).

Firmware

To SAGEMCOM router [email protected] 2804 v7 worked better, it can be flashed to the latest version. In the "Device Information" item, you will find out the current software version.

You can find the latest firmware on the developer's website.

After downloading the firmware to your PC, you can start the installation. This is done in the "Software Update" section of the "Management" section. Click on "Select file" and enter the path to the program. Now it remains to click on "Update".

The flashing process will take some time, but you should not turn off or reboot the equipment. After the procedure, the product will independently reboot.

Internet

Special problems when configuring SAGEMCOM [email protected] 2804 v7 from Rostelecom is not. All manipulations are performed through the interface. First, we recommend that you register the route "192.168.1.1" and enter authorization data. For a new product, the keyword admin is suitable for both fields, and if there are no changes, then press reset.

So, the setup begins with the creation of a PVC connection. Locate "ATM PVC Interface". Having done this, click on "Add" and set the following parameters:

• VPI/VCI - 0/33;
• Encapsulation mode - LLC;
• DSL Link type - EoA.

Then add a connection through the "WAN service" (click on "Add" in this window). The physical interface is recommended to be set to atm0.

Interestingly, the network here can be selected as "Bridge" or "Router". The system will prompt you to make this choice during setup.

When using a PPPoE connection, enter the following data in the proposed fields:

• login/pass - enter the data provided in the contract;
• in case of an error not to repeat PPP authentication, check the box next to this item;
• service name - come up with a name for your network;
• auto authentication.

Also enable Firewall and NAT (these fields may be absent in some firmwares). You do not need to touch other fields, click "Apply".

Now re-enter the login / pass of the router, issued by the company, in the “Internet Connection”, and then reboot the device to get started.

WiFi setup

Wi-Fi on SAGEMCOM [email protected] 2804 v7 from Rostelecom is configured very quickly. Select "Enable Wi-Fi" in the "WLAN Setup" item, and enter the following in the "Security" section:

• WPS - Disable;
• type - WPA2-PSK;
• SSID - enter the name of the network;
• encryption - AES;
• password - create a strong key.

This article is about the Sagemcom device [email protected] 2804. In the recent past, it has been actively promoted by Rostelecom and MTS. The latter supplies it under the name "MTS Universal Router".

Upon closer examination, it turns out that this device combines the functions of a 3G, ADSL, and Ethernet router. In addition, it can work as a wi-fi hotspot that supports 802.11 n/g/b. From additional bonuses: supported IPTV. The package bundle of the router does not shine with wealth, but, nevertheless, everything you need is available.

Please note that MTS offers two models that differ in appearance and software (V1 and V3). The latest firmware versions of the MTS universal router allow you to connect more than 13 modem models to it.

By the way, you can download the latest software version, installation and recovery instructions on the official website.

Rostelecom offers a version of the device V7. But the presence of fresh software, their site, unfortunately can not boast. There is only a brief specification of the device universal router f st 2804, and instructions.

The router, manufactured by Sagemcom, allows you to connect to the Internet through a high-speed connection.

The most notable features of this router:

1. high-speed connection via a telephone cable, while the phone itself is free;
2. support for IPTV transmission to a digital set-top box;
3. accessing and managing multimedia content.

The device is equipped with a modern, powerful processor that allows you to connect to the Internet at maximum speed, in addition, it is possible to view several high-definition IPTV channels at the same time.

Wireless interface device router fast 2804 V7

The Sagemcom router supports the 801.11b/g/n WFA specification. It also has a 2x2 transceiver configuration, thanks to which the real connection speed reaches 80 Mbps. Modern security protocols supported are: MAC address filtering, WPA, WPA2, WEP. The router is equipped with an automatic radio channel selection function and a separate button, which provides convenient and easy wireless connection according to the WPS protocol. There is an additional button on the body that turns on the wireless interface.

multimedia content

The device is capable of working as a DLNA server version 1.5, supporting Webdav, Samba, UPnP protocols, which allows access to multimedia content from any device. There are two USB ports through which access to a printer or external storage can be provided.

Router Features

The router has support for a large number of IP services applicable to double-play routers:

• IGMP proxy/snooping
• DNS dynamic/server/relay
• DHCP relay/server/client
• Full speed IP routing

Firewall

Router 2804 v7 has a firewall with the following features:

• Complete address/protocol filtering/port
• Stateful Packet Inspection

Configuring traffic through the application firewall:

• VoIP services based on H.323 and SIP
• a large number of web applications

Connection on the example of a device from MTS

The 2804 router makes it possible to implement a broadband Internet connection in an office or home network through channel redundancy:

• 3G modem, Wimax, Fon;
• on PC and TV IP-TV;
• Wi-Fi wireless connection (802.11 n\b\g)

The modem is connected in the following order. In the RJ-11 connector, through the splitter, we connect the cable. The universal router is connected to the computer via an Ethernet cable; for this, four connectors are placed behind the router. An external modem is connected to the USB port, then the router itself is connected to the network.

An external modem can reserve an Internet channel. If the main channel is interrupted, the device will automatically switch to connection via an external modem.

Setting up a router

After establishing an Ethernet connection, open the browser and enter the IP address of the device. The default address is set to 192.168.1.1. After that, the system will require authorization. Enter your username and password, or leave the default one, then all the settings necessary for working with the Internet appear in the window that opens: universal router settings, connection settings, channel configuration, wireless connection.

In a separate tab, advanced configuration of the f st 2804 router is performed, which is required by experienced users. After you enter and save the required data, the connection setup is completed.

It was mentioned above about the possible reservation of the channel for those cases when the main connection is broken. This is done in the next tab: "3G channel configuration". We put a tick in the enable point, and after 15 seconds. the device will automatically switch to the connection via the backup channel. When the main connection is restored, the router will automatically switch back.

Setting up a wireless connection, in the basic parameters, contains: enabling the WLAN module, the function of not detecting an access point, the MAC address of the wireless connection, network authentication and selecting the channel through which the router communicates with clients.

In the "Management" tab, you can back up the setup data, update or restore the system. After updating the device software, previously used settings are retained. The update takes a couple of minutes.

Let's summarize the above

The fast 2804 universal router is large, but very easy to use. The functionality of the device is high, it is possible to implement all the necessary resources, including backup switching from the main connection to the additional one. All of the above gives reason to believe that the Sagemcom universal router will be one of the most convenient options for implementing office or home communications.

This review will step by step review and describe the Sagemcom F ST 2804 V7 setup. This is an entry-level router, which is often sold in addition to the services provided by domestic providers. These include the nationwide MTS and Rostelecom. It is on the example of configuring the connection of such a router to the network equipment of the last company that this material will be presented.

Network Gateway Package

Standard and typical delivery list for this router. Separately, it should be noted that such a network gateway is tied to the equipment of a particular provider. That is, if the router is designed to work in combination with the software and hardware of the Rostelecom company, then it will only work in such a bundle.

The delivery list includes a Sagemcom F ST 2804 V7 router. Setting up a Rostelecom connection is described in detail in the instruction manual. The manufacturer did not forget to include a warranty card in the package, the validity of which is 1 year. This is a complete list of the configuration of this solution. This list is supplemented by a power supply with a 0.5 A output and an interface cord, which is mainly used at the stage of setting up a network connection.

Also in the delivery list there is a CD with specialized software. By default, the hero of this article has the V5 software version, which cannot work normally with Rostelecom equipment. Therefore, it is necessary to upgrade the router considered in this material to version V7.

main parameters

The main parameters of this router are as follows:

• Three possible ways to connect to the Internet: Ethernet, ADSL and 2G / 3G (in the latter case, you must additionally purchase an external modem and a starter pack to be able to connect to a cellular network).
• Four RJ-45 ports, which can be used both for connecting computing devices via twisted pair to the global web, and switching set-top boxes.
• One USB standard port, which is used to connect a modem.
• A wireless network based on a Wi-Fi transmitter, within which information can be transmitted at speeds up to 300 Mbps.

The body of this device is plastic. May be white or black. Information LEDs are displayed on one side of it. The first of them indicates the presence of power, the second indicates an active ADSL connection, the third indicates the presence of receiving information from the Internet. The next information indicator indicates the operation of the wireless network. Then there are four LEDs that characterize the functioning of the wired segment of the internal computer network. The last light element in this case shows the operation of the USB port built into the router.

On the top side of the device are a USB connector and two buttons. One of them includes a network gateway of this model, and the second uses the technology of automatically connecting the device using Wi-Fi.

On the opposite side face from the information panel, all connection ports are displayed. These include an ADSL connector, a USB port, and 4 RJ-45 ports. There is also a power socket here. There is also a button to reset the software to its original state.

Connection

At the first stage, setting up the Sagemcom F ST 2804 V7 comes down to making the following connections:

1. We install the router at the place of use. The latter must meet the following requirements: there must be an outlet as close as possible, an ADSL input wire and interface cords from computers must be connected.
2. Next, connect the power supply.
3. Then it is necessary to carry out switching with the equipment of the ADSL provider.
4. The last stage is the collection of the wired part of the computer network.

Setting up an external wired connection

At the first stage, you need to update the software shell of the router. To do this, on the PC connected to the network gateway, launch the CD and in the autorun window that opens, select the “Update router” item and wait for this operation to complete.

Then setting up the Sagemcom F ST 2804 V7 comes down to configuring the external connection. To do this, we re-initialize the launch of the CD and select the “Full Setup” item in its menu. In the future, follow the instructions of the wizard and set the connection parameters, which can be taken from the contract with the provider for the provision of services. At the end, save the entered data and exit the setup wizard.

Modem setup

The next step is to configure the Sagemcom F ST 2804 V7 modem, which is used to implement a backup method for connecting to the Internet. It consists of the following actions:

1. Choose a supported 3G modem model, purchase it along with the starter pack. We collect everything together and connect to the router.
2. We launch any available browser on a PC that is directly connected to the network gateway.
3. In its address bar, enter the device address in the format 192.168.1.1.
4. Next, in the request window in the fields "Login" and "Password" you must enter admin. After that, press the "Login" button.
5. Go to "Advanced Settings" and select the "3G Configuration" sub-item.
6. Then we set the PIN code for the installed SIM card.
7. We save the data and exit the program shell.

Setting up an internal connection

The wired connection is automatically configured, and there is no need to perform any additional manipulations with the Sagemcom F ST 2804 V7 program parameters. Wi-Fi setup is also automatic. The only thing you will definitely need is to rewrite the network name and password to connect to it from the bottom cover of the device case. In the future, simply enter them in the appropriate request.

IPTV

The router in question supports IPTV technology, with which you can watch television programs. In this case, the step-by-step configuration of the Sagemcom F ST 2804 V7 router is performed as follows:

1. We go into the router settings menu according to the previously given method.
2. After opening the settings interface, you need to go to the sub-item "Advanced Settings". Then you need to select "Interface grouping".
3. At the next stage, click the "Add" button and set the connection port of the IPTV set-top box.
4. Save the settings and exit the setup interface.

Price

At the moment, such a router can be purchased for 1200-1500 rubles. Again, it is advisable to purchase such a solution only if Rostelecom acts as a provider of Internet traffic. Given the functionality of the device in question, such a cost is fully justified.

Conclusion

Sagemcom F St 2804 V7 is a very high-quality, functional and at the same time very affordable network gateway. Setting it up is a fairly simple operation, and every user is able to handle it. The provider at the same time simplified the process of its implementation as much as possible. Therefore, such a router is simply ideal for creating home computer networks.