Instrumentation adjuster: what kind of profession, ranks, training. Profession instrumentation fitter: knowledge and job responsibilities

Section "Locksmith and locksmith and assembly work"

§94. Locksmith for instrumentation and automation

4th category

Characteristics of works. Repair, adjustment, testing, adjustment, installation and commissioning of complex electromagnetic, electrodynamic, heat-measuring, optical-mechanical, counting, automatic, pyrotechnic and other devices with fitting and fine-tuning of parts and assemblies. Adjustment and adjustment of relay "protection devices, electrical automation, telemechanics. Determination of defects in repaired devices and elimination of them. Locksmith processing of parts according to 7-10 qualifications and assembly of gear and worm gears. Drawing up and installation of complex connection diagrams. Calculation of absolute and relative errors when checking and testing devices.Compilation of defective statements and filling in passports and certificates for devices and machines.

Should know: device, principle of operation and methods of adjustment of repaired and adjusted complex devices, mechanisms, devices; purpose and methods of adjustment of control and measuring and control and quotation instruments; methods of adjustment and calibration of instruments and apparatus and rules for taking characteristics during their testing; rules for calculating resistances; schemes of complex connections; rules for calculating absolute and relative errors when checking and testing devices; designations of thermal and electrical circuits and drawings; system of admissions and landings; quality and roughness parameters; fundamentals of mechanics and electronics in the scope of the work performed.

2. Film projection equipment - replacement of individual components and parts.

3. Adding machines and typewriters of all systems - overhaul and restoration.

4. Accurate analytical scales - repair, adjustment.

5. Scales bunker elevator - current, average and capital repairs, adjustment and check.

6. Commercial and automobile scales with rocker indicating devices - overhaul.

7. Scales for commodity and automobile scales with a dial pointing device - overhaul, medium and current repairs.

8. Scales mortise commodity mobile and stationary - current, average and capital repairs, installation, adjustment, check.

9. Viewfinders - repair, adjustment.

10. Water meters of all systems and all diameters in wells - installation with switching to other diameters, medium repairs.

11. Rectifiers - revision and repair.

12. Self-recording galvanometers and logometers - disassembly and repair.

13. Cinema and photographic equipment - repair of synchronizers; diaphragms of deceleration mechanisms, rangefinder adjustment.

14. Gear wheels - finishing the keyway with a nozzle on the axle.

15. Magnetic contactors, marine starters - medium repair.

16. Clock mechanisms of all kinds of instruments (pressure gauges, traction gauges, etc.) - overhaul with the manufacture of parts and adjustment,

17. Microscopes - repair with fine-tuning of parts and alignment.

18. Pressure gauges and indicators - disassembly, repair, assembly and adjustment.

Characteristics, works. Repair, adjustment, testing and commissioning of simple, magnetoelectric, electromagnetic, optical-mechanical and heat measuring instruments and mechanisms. Locksmith processing of parts according to 12 - 14 qualifications. Determining the causes and troubleshooting of simple devices. Installation of simple wiring diagrams. Winding springs from wire in a cold state, protective lubrication of parts. Repair of devices of medium complexity under the guidance of a more highly qualified locksmith.

Must know: device, purpose and principle of operation of repaired devices, mechanisms; schemes of simple special adjusting installations; basic properties of conductive and insulating materials and methods for measuring resistance in various links of the circuit; purpose and rules for the use of the most common universal and special devices and instrumentation; system of admissions and landings; quality and roughness parameters; grades and types of anti-corrosion oils and lubricants; name and marking of processed materials; fundamentals of electrical engineering in the scope of the work performed.

Work examples

1. Ammeters, voltmeters, pressure gauges, galvanometers - medium repair and adjustment.

2. Carriage scales - processing of various parts.

3. Commercial scales, mobile and stationary (mortise) - replacement and repair of platform flooring and weight holders.

4. Weights trade and conditional - repair and delivery under branding.

5. Details simple to devices - metalwork with threading in through holes.

6. Frames for transformers - manufacturing.

7. Gear wheels with a futor - picking.

8. Cinema and cameras - change of eyepieces, locks, caps, repair of frame counters.

9. Magnetic contactors and starters - medium repair.

10. Technical pressure gauges - assembly.

11. Millivoltmeters - medium repair, verification and delivery after testing.

12. Relay base - template assembly.

13. Instruments - setting to mechanical zero.

14. Trailers, binoculars, spotting scopes - repair and adjustment.

15. Piezoacoustic transducers, electromagnetic sensors - medium repair.

16. Copper conductors for resistances - billet.

17. Regulators, distributors and large relays - repair.

18. Copper and platinum resistance thermometers - assembly and calibration.

19. Contact thermocouples - assembly and adjustment.

20. Clamps of complex configuration - manufacturing.

21. Gears, bushings, mounting rings and other parts - pinning on rollers, drilling and reaming holes for pins.

Test your strength

• Online tests
• Online computer science tests
• Online Physics Tests
• Online math tests
• Online tests in Russian
• Occupation Tests
• Is an industrial designer right for you?
• What kind of economist are you?
• Test "Professional suitability"
• Do you want to become a cyber cop?
• Educational quizzes
• Physics test on the topic "Problem Solving" (Grades 7-9)
• Final test in mathematics (grade 6)
• Informatics test for grades 10-11
• Processing materials by pressure, or how to bend a lamppost.
• Informatics test for grade 5 "Information around us"

Occupation Tests

• Profession choice matrix (G.

Instrument fitter: what kind of profession, ranks, training

Adjustment, testing and delivery of blocks of medium complexity and power systems, instruments and information-measuring systems; checking the electrical parameters of the regulated equipment using instrumentation.3. Drawing up layout diagrams for regulation and testing of complex mechanisms, devices, systems. Requirements for education and training. Secondary vocational education - training programs for skilled workers (employees).
Requirements for practical work experience. At least one year of work on the second qualification level in the profession "Mechanic-adjuster of instrumentation and automation". Special conditions for admission to work.

Vacancies and work: “Kipia adjuster” in st. petersburg

To carry out heat treatment of low-responsibility parts with their subsequent fine-tuning; 7. Determine the hardness of the metal with calibrated files; 8. Repair, adjust and adjust especially complex instruments and devices under the guidance of a more highly qualified locksmith; (hereinafter - the general qualification requirements given in the qualification characteristics for the 2nd category, section "must be able", paragraphs.

7-12.). CURRICULUM for retraining and advanced training of workers in the profession "Mechanic for instrumentation and automation" of the 3rd category Training period 2 months No. p / p Content (courses, subjects) Number of hours 1 General technical course 54 1.1 Fundamentals of a market economy 4 1.2 Electrical engineering 10 1.3 Materials science 8 1.4.

Adjuster of instrumentation and automation

Important

Basics of mechanics and electronics in the scope of the work performed (hereinafter referred to as the general qualification requirements given in the qualification characteristic for the 2nd category, section "must know", paragraphs 8-13). A locksmith for instrumentation and automation of the 4th category must be able to: 1. Repair, adjust, test, adjust, install and commission complex - electromagnetic, electrodynamic, heat-measuring, optical-mechanical, counting, automatic, pyrotechnic and other devices with adjustment and fine-tuning of critical parts and assemblies; 2.

Perform configuration and adjustment of relay protection devices, electrical automation, telemechanics; 3. Determine the defects of the repaired devices and eliminate them; 4. Perform metalworking of parts according to 7-10 grades (8-3 accuracy classes) and assembly of gears and worm gears; 5.

Compile and assemble complex wiring diagrams; 6.

Work as a fitter of instrumentation in st. petersburg

Qualification — 6th grade A locksmith for instrumentation and automation of the 6th grade must know: 1. The device, the interaction of especially complex devices, the technological process of their assembly and adjustment methods; 2. Electrical thermal diagrams of thermal automation devices; 3. Device and methods of alignment of complex control and adjustment devices; 4. Properties of optical glass, metals and auxiliary materials, conductors, semiconductors used in instrument making; 5. Fundamentals of calculation of gears of various gearing profiles and optical systems; 6.
Fundamentals of physics, mechanics, telemechanics, heat engineering, electrical engineering, metrology, radio engineering and electronics in the scope of the work performed: (hereinafter - the general qualification requirements given in the qualification characteristic for the 2nd category, section "must know", paragraphs 7-12) .

Mo

Adjustment of simple electronic heat engineering devices, automatic gas analyzers, control and measuring, electromagnetic, electrodynamic mechanisms with fitting and fine-tuning of parts and assemblies.2. Adjustment of control circuits for contact-relay, ionic, electromagnetic and semiconductor electric drives.3. Testing and delivery of elements and simple electronic components with the removal of characteristics.4.
Drawing up and layout of simple and medium complexity schemes. Requirements for education and training. I. Secondary general education. II. Vocational training programs for the training of skilled workers.
Special conditions for admission to work.
The presence of the II qualification group in electrical safety. Passage by the employee of fire-fighting briefing. Passage by the employee of briefing on labor protection at the workplace. established by the legislation of the Russian Federation. Instrumentation adjuster of the 4th category Instrumentation adjuster of the 4th category Generalized labor function. Adjustment, verification and commissioning of complex schemes. List of labor functions. 1. Adjustment, verification and commissioning of complex schemes of industrial automation, telemechanics, communications, electronic-mechanical testing and electro-hydraulic machines and stands equipped with information-measuring systems.2.

Availability of a qualification group for electrical safety Passage by the employee of fire safety briefing Passage by the employee of briefing on labor protection at the workplace Passage of mandatory preliminary (upon admission to work) and periodic medical examinations (examinations), as well as extraordinary medical examinations (examinations) in the manner prescribed the legislation of the Russian Federation. Instrumentation adjuster of the 5th category Instrumentation adjuster of the 5th category Generalized labor function. Adjustment, adjustment and commissioning of complex instrument systems and equipment control systems based on microprocessor technology.

List of labor functions. 1. Adjustment, adjustment and commissioning of complex systems of instruments and equipment control systems based on microprocessor technology.2.

Instrument fitter 2nd category

Attention

QUALIFICATION CHARACTERISTICS Profession - mechanic for instrumentation and automation. Qualification - 2nd category. A locksmith for instrumentation and automation of the 2nd category must know: 1. Purpose, design and principle of operation of the repaired devices, mechanisms; 2.

Schemes of simple special adjustment settings; 3. The main properties of conductive and insulating materials, the purpose and rules for the use of the most common universal and special devices of medium complexity and accuracy of the control and measuring instrument; 4. Basic information about tolerances and fits, qualifications (accuracy classes) and roughness parameters (machining cleanliness classes); 5. Varieties and types of anti-corrosion oils and lubricants; 6. Name and marking of processed materials; 7. Fundamentals of electrical engineering in the scope of the work performed; eight.

Instrument fitter etc

The profession of a mechanic dealing with instrumentation is becoming more and more relevant every day. What is the reason? This will be discussed further. Who is an I&C engineer? Almost any enterprise has a variety of different instruments, sensors, meters and other technical devices. All such equipment must be supervised by someone.

The instrumentation adjuster is the very specialist who is able to control the safe and efficient operation of all devices available in the production. So, a professional is obliged to conduct a periodic inspection of the equipment, its high-quality repair or replacement. It should be noted right away that the profession in question is not so simple.

After all, a competent specialist must have a fairly wide range of knowledge, skills and abilities. Without all this, it will not be possible to carry out their work functions qualitatively.

rb instrumentation etks

Geography932

• History2322
• Literature1367
• English language 1948
• German579
• Tatar language520
• MHK201
• Astronomy20
• Technology180
• Physical education239
• OBJ100
• Economy80

All Items25131 Question Board Popular Questions

• Krivtsov Maxim: Transfer to MDK (Moscow Road College) from LKTiDH (Lipetsk College of Transport and Road…0
• Kolesnikova Arina: ege 20181
• karolinane:Admission to university2
• Mukha Maxim: transfer to study at a Russian university1
• Novikova Olga:Admission to the faculty of journalism1
• Anastasia Adamenko: How to become a tourism manager1

Ask a question5404 questions asked Reviews about universitiesMoscow

• StudentNational Research University "MPEI" I am satisfied with the university) The teachers are good, they are looking for an individual approach to everyone.

None of my group had a problem with them. After the 3rd Course, they are distributed to practice. Yes, and after studying it is easy to find ...

• StudentState University of Management Decent university, good quality of education, pleasant environment 🙂
• Graduate The Moscow Financial and Law University MFLA has truly become my home. The level of education and administration support is top notch. To feel the atmosphere of MFUA, you need to be a student of MFUA)

Rate University College ReviewsMoscow

• Graduate Russian Humanitarian and Technical College "Tantal" COLLEGE "TANTAL" HELPED ME VERY IN MY WORK AND IN MY HOBBY OF RADIO AMATEURS, I STILL STORE AND USE THE EDUCATIONAL MATERIALS.
• StudentCollege of Architecture and Construction No. 7 I am a 4th year student. Three years flew by completely unnoticed.

Instrument fitter: what kind of profession, ranks, training

Content (courses, subjects) Number of hours 1 General technical course 54 1.1 Fundamentals of market economy 4 1.2 Electrical engineering 10 1.3 Materials science 8 1.4. Drawing (reading drawings) 14 1.5 Tolerances and technical measurements 10 1.6 Industrial safety and labor protection 8 2 Special course 60 2.1 Introduction 2 2.2 Occupational health, industrial sanitation and injury prevention 2 2.3 Rules for the repair of instrumentation 20 2.4 Weighing devices 18 2.5 Optical -mechanical devices 18 3 Industrial training 192 3.1 Training on the training ground 30 3.2 Training on the production 162 4 Consultations 6 5 Exam 8 Total 320 QUALIFICATION CHARACTERISTICS Profession - mechanic for instrumentation and automation.

Vacancies and work: “Kipia adjuster” in st. petersburg

Requires secondary vocational education. Comments on the profession The given tariff and qualification characteristics of the profession "Adjuster of instrumentation and automation" are used to rate work and assign wage categories in accordance with Article 143 of the Labor Code of the Russian Federation. Based on the above characteristics of work and the requirements for professional knowledge and skills, a job description is drawn up for an adjuster of instrumentation and automation, as well as documents required for interviewing and testing when applying for a job.
When compiling work (job) instructions, pay attention to the general provisions and recommendations for this issue of the ETKS (see the "Introduction" section). We draw your attention to the fact that the same and similar names of working professions can be found in different issues of ETKS.

Adjuster of instrumentation and automation

Tolerances and fits, qualifications (accuracy classes) and roughness parameters (machining cleanliness classes); (hereinafter - the general qualification requirements given in the qualification characteristics for the 2nd category, section "must know", paragraphs 8-13). A locksmith for instrumentation and automation of the 3rd category must be able to: 1.

Repair, assemble, check, adjust, test, adjust, mount and hand over heat-measuring, electromagnetic, electrodynamic, counting, optical-mechanical, pyrometric, automatic, self-recording and other devices of medium complexity with the removal of circuits; 2. Perform metalwork, processing of parts according to 11-12-level quality (4-5th accuracy class) with fitting and fine-tuning of parts; 3.

Draw up and mount circuits of medium complexity; 4. Paint appliances; 5. Perform soldering with various solders (copper, silver, etc.).

6.

Work as a fitter of instrumentation in st. petersburg

Mount simple wiring diagrams; 5. Wind springs from wire in a cold state, perform protective lubrication of parts; 6. Repair appliances of medium complexity under the guidance of a more highly qualified locksmith; 7.

Attention

Economical and rational use of raw materials, fuel - energy and material resources; 8. Maintain established technical documentation; 9. Timely and rationally prepare for work and clean the workplace; ten.

Mo

Who is cooler? Choose a profession that you like more! Your opinions form the rating of professions Already 1691560 votes! Technician for the installation and operation of equipment and gas supply systems Logistician Average salary in Moscow: average in St. Petersburg: What specialty do you need to get

• Relay protection and automation of electric power systems (Basic training)
• Relay protection and automation of electric power systems (Advanced training)
• Electrical Machines and Apparatus (Basic Training)
• Electrical Machines and Apparatus (Advanced Training)
• Power stations, networks and systems (Basic training)
• Power stations, networks and systems (Advanced training)

Do you know a specialty that suits this profession? Write to us.
Industrial safety and labor protection 8 2 Special course 60 2.1 Introduction 2 2.2 Occupational health, industrial sanitation and injury prevention 2 2.3 Weighing devices 4 2.4 Installation of electrical wiring 4 2.5 Arrangement of writing, recording and computing machines 6 2.6 Arrangement of opto-mechanical devices 8 2.7 Capital repair of instrumentation and automation equipment 8 2.8 Instruments for measuring level and flow 12 2.9 Electrical control equipment 6 2.10 Wear and lubrication of instrumentation, mechanisms and automation equipment, methods of restoration and hardening of parts 4 2.11 Organization of a repair service and a preventive maintenance system 4 3 Industrial training 192 3.1 Training at the training ground 30 3.2 Training at the workplace 162 4 Consultations 6 5 Exam 8 Total 320 QUALIFICATION CHARACTERISTIC Profession - mechanic in instrumentation and automation.

Vacancies found: 1 929 Average salary: 46 371 rub. Instrumentation adjuster from 32,200 rubles, Full, from 3 to 6 years, Commercial Responsibilities: Repair, adjustment, installation, testing, adjustment, adjustment and calibration of automatic electronic equipment, instruments, measuring instruments (pressure, temperature, ... Full description, St. Petersburg - hh: 11 hours ago I&C adjuster from 35,000 rubles, Full, from 3 to 6 years, Commercial Responsibilities: Maintenance of devices and automation of modern electroplating production, water treatment, ventilation systems Requirements: Education not lower than secondary ... Full description, St. Petersburg - hh: 11 hours ago Adjuster from 60,000 rubles, full-time, no experience Responsibilities: — Setting up the equipment and optimizing its operation modes to achieve the quality of the output products of the corresponding specifications, and reduce the number of defects.

Instrument fitter 2nd category

Radio units - connecting the unit to the mains in a circuit with a power supply, setting the wavelength of the high-frequency part, removing the DC mode, checking the radio frequency gain. 16. Systems of calculating devices - adjustment. 17. Metal-cutting machines of varying complexity and with program control, equipment for flexible technological processes - adjustment of automation.
18.

Important

Television and electronic-mechanical plotters - adjustment. 19. Amplifiers of high and low frequency (two to five stages of amplification) - adjustment with adjustment and adjustment of all parameters of incoming radio tubes, tuning of local oscillator circuits and equalization of the frequency band in band-pass amplifiers and cutoff filters, resonance tuning, removal and plotting frequency characteristics.

Instrument fitter etc

Calculate absolute and relative errors when checking and testing devices; 7. Draw up defective statements and fill out passports and certificates for devices and machines; (hereinafter - the general qualification requirements given in the qualification characteristic for the 2nd category, section "must be able", paragraphs 7-12). CURRICULUM for advanced training in the profession "Mechanic for instrumentation and automation" 4th category Training period 2 months No. p / p Content (courses, subjects) Number of hours 1 General technical course 54 1.1 Fundamentals of a market economy 4 1.2 Electrical engineering 10 1.3 Materials science 8 1.4.

rb instrumentation etks

About the 6th and 7th category in the profession The ranks of an instrumentation and automation adjuster indicate a lot: the level of education, work experience, professional skills, etc. The 6th and 7th levels of qualification are considered quite important and prestigious. What types of work are typical for specialists with the 6th category?

• Adjustment on the existing equipment of autoregulators and heat meters.
• Repair of electronic equipment.
• Work with automatic portion scales.
• Work with wagon exemplary scales.
• Repair of oscilloscopes.
• Works with magnetic amplifiers.
• Repair, adjustment and commissioning of various electronic selection devices.

What types of work are typical for a specialist with a 7th grade? Here are some examples:

• testing and verification of microprocessor devices (pressure sensors, differential pressure gauges, etc.);

This job description has been translated automatically. Please note that automatic translation does not provide 100% accuracy, so there may be minor translation errors in the text.

Preface to job description

0.1. The document comes into force from the moment of its approval.

0.2. Document developer: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.

0.3. Document approved: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _.

0.4. Periodic verification of this document is carried out at intervals not exceeding 3 years.

1. General Provisions

1.1. The position "Mechanic for instrumentation and automation of the 2nd category" belongs to the category "Workers".

1.2. Qualification requirements - complete general secondary education and vocational training at work, without requirements for work experience.

1.3. Knows and applies:
- device, purpose and principle of operation of devices, mechanisms that are being repaired;
- diagrams of simple special control installations;
- basic properties of conductive and insulating materials and methods for measuring resistance in various links of the circuit;
- the purpose and rules for the use of the most common universal and special devices and the average complexity and accuracy of the control and measuring tool;
- basic information about tolerances and fits, qualifications (accuracy classes) and roughness parameters (machining cleanliness classes);
- varieties and types of anti-corrosion oils;
- the name and marking of the materials that it processes;
- the basics of electrical engineering in the scope of work that performs.

1.4. A locksmith for instrumentation and automation of the 2nd category is appointed to the position and dismissed from the position by order of the organization (enterprise / institution).

1.5. The locksmith for instrumentation and automation of the 2nd category reports directly to _ _ _ _ _ _ _ _ _ _ .

1.6. A locksmith for instrumentation and automation of the 2nd category directs the work of _ _ _ _ _ _ _ _ _ _ .

1.7. The locksmith for instrumentation and automation of the 2nd category during the absence is replaced by a person appointed in the prescribed manner, who acquires the appropriate rights and is responsible for the proper performance of the duties assigned to him.

2. Description of work, tasks and job responsibilities

2.1. Repairs, regulates, tests and delivers simple magnetoelectric, electromagnetic, optical-mechanical and thermal imaging devices and mechanisms.

2.2. Performs metalwork processing of parts according to 12 - 14 grades (5 - 7 classes of accuracy.

2.3. Determines the causes and eliminates malfunctions of simple devices.

2.4. Mounts simple wiring diagrams.

2.5. Winds springs from wire in a cold state, performs protective lubrication of parts.

2.6. Repairs devices of medium complexity under the guidance of a highly qualified locksmith.

2.7. Knows, understands and applies the current regulatory documents relating to its activities.

2.8. Knows and fulfills the requirements of regulatory acts on labor and environmental protection, complies with the norms, methods and techniques for the safe performance of work.

3. Rights

3.1. The Mechanic for Instrumentation and Automation of the 2nd category has the right to take actions to prevent and eliminate the occurrence of any violations or inconsistencies.

3.2. A locksmith for instrumentation and automation of the 2nd category has the right to receive all social guarantees provided for by law.

3.3. A locksmith for instrumentation and automation of the 2nd category has the right to demand assistance in the performance of his duties and the exercise of rights.

3.4. A locksmith for instrumentation and automation of the 2nd category has the right to demand the creation of organizational and technical conditions necessary for the performance of official duties and the provision of the necessary equipment and inventory.

3.5. A locksmith for instrumentation and automation of the 2nd category has the right to get acquainted with draft documents relating to his activities.

3.6. A locksmith for instrumentation and automation of the 2nd category has the right to request and receive documents, materials and information necessary for the performance of his duties and orders of the management.

3.7. A locksmith for instrumentation and automation of the 2nd category has the right to improve his professional qualifications.

3.8. The locksmith for instrumentation and automation of the 2nd category has the right to report all violations and inconsistencies identified in the course of his activities and make proposals for their elimination.

3.9. A locksmith for instrumentation and automation of the 2nd category has the right to familiarize himself with documents defining the rights and obligations of his position, criteria for assessing the quality of performance of official duties.

4. Responsibility

4.1. The locksmith for instrumentation and automation of the 2nd category is responsible for non-fulfillment or untimely fulfillment of the duties assigned by this job description and (or) non-use of the rights granted.

4.2. A locksmith for instrumentation and automation of the 2nd category is responsible for non-compliance with the rules of internal labor regulations, labor protection, safety, industrial sanitation and fire protection.

4.3. A locksmith for instrumentation and automation of the 2nd category is responsible for disclosing information about an organization (enterprise / institution) that is a trade secret.

4.4. The locksmith for instrumentation and automation of the 2nd category is responsible for non-fulfillment or improper fulfillment of the requirements of the internal regulatory documents of the organization (enterprise / institution) and the legal orders of the management.

4.5. A locksmith for instrumentation and automation of the 2nd category is responsible for offenses committed in the course of his activities, within the limits established by the current administrative, criminal and civil legislation.

4.6. A locksmith for instrumentation and automation of the 2nd category is responsible for causing material damage to an organization (enterprise / institution) within the limits established by the current administrative, criminal and civil legislation.

4.7. The locksmith for instrumentation and automation of the 2nd category is responsible for the misuse of the granted official powers, as well as their use for personal purposes.

5. Examples of work

5.1. Ammeters, voltmeters, ammeters, galvanometers - medium repair and adjustment.

5.2. Carriage scales - processing of irresponsible details.

5.3. Scales commodity mobile and stationary (mortise) - replacement and repair of a flooring of platforms and giretrimach_v.

5.4. Weights trade and conditional - repair and delivery under branding.

5.5. Details are simple in devices - metalwork with threading in through holes.

5.6. Frameworks for transformers - production.

5.7. Cinema - and cameras - replacement of glasses, locks, caps, repair of frame counters.

5.8. Gear wheels with a futor - picking.

5.9. Magnetic contactors and starters - medium repair.

5.10. Technical pressure gauges - compilation.

5.11. Millivoltmeters - medium repair, verification and delivery after testing.

5.12. The basis of the relay is drawing up according to a template.

5.13. Transducers p "ezoacoustic, electromagnetic sensors - medium repair.

5.14. Devices - setting to mechanical zero.

5.15. Sights, binoculars, spotting scopes - repairs and adjustments.

5.16. Copper conductors for resistances - blanks.

5.17. Regulators, distributors and large relays - repairs.

5.18. Contact thermocouples - drafting and regulation.

5.19. Copper and platinum resistance thermometers - compilation and calibration.

5.20. Clamps of complex configuration - manufacturing.

5.21. Gears, bushings, adjusting rings and other details of pins on rollers, drilling and reaming holes for pins.